Wear-resistance of high entropy cutting-tool materials
https://doi.org/10.12737/20216
Abstract
The work objective is to study the wear resistance of the experimental hard alloys (EHA) and complex alloyed high-speed steels (HSS) under cutting, as well as to establish the interconnection between their tribological characteristics and the entropy values (thermal EMF). The experimental studies on the EHA wear are carried out under the longitudinal turning, and HSS - under the friction conditions and drilling operations. Molybdenum, iron, titanium and copper mono carbide alloys are inserted into the cobalt bonds. It is shown that in this case, both entropy and wear-resistance increase (up to 2.5-3 times) as compared to the VK8 base alloy. At the same time the optimum machining spectrum extends. The functional relation between entropy and thermal EMF of the HSS is established, and it is shown that the minimum values of the thermal EMF correspond to the high entropy values. The HSS wear rate under friction is lower and the guaranteed life of drills is higher in steels with a high entropy value. The results obtained should be applied to the forming operations for the cutting-tool materials (CTM) of the maximum wear-resistance, and when developing new CTM.
About the Authors
Anatoly A. Ryzhkin
Don State Technical University
Russian Federation
Russian Federation
Anatoly I. Bokov
Don State Technical University
Russian Federation
Russian Federation
Yulia A. Oleynikova
Don State Technical University
Russian Federation
Russian Federation
References
1. Ryzhkin, A.A., et al. Termodinamicheskiy metod otsenki intensivnosti iznashivaniya trushchikhsya materialov. [Thermodynamic method for estimating wear rate of rubbing materials.] Journal of Friction and Wear, 1982, vol. 3, no. 5, pp. 867–872 (in Russian).
2. Ryzhkin, A.A. Obrabotka materialov rezaniem: fizicheskie osnovy. [Materials cutting: physical fundamentals.] Rostov-on-Don: DSTU Publ. Centre, 1996, 242 p. (in Russian).
3. Ryzhkin, A.A. Obrabotka materialov rezaniem. [Materials cutting.] Rostov-on-Don: DSTU Publ. Centre, 1995, 256 p. (in Russian).
4. Ryzhkin, A.A., et al. Otsenka rabotosposobnosti vysokoentropiynykh instrumental'nykh rezhushchikh materialov. [Determination of the efficiency of high- entropy cutting tool materials.] Journal of Friction and Wear, 2016, vol. 37, no. 1, pp. 47–54 (in Russian).
5. Ryshkin, A. Über Reibung und Verschleiss bei der Zerspanung mit W-Co und W-frei beschichteten Schneidwerkzeugen. 14th International Plansee Seminar'97: Proceedings. Reutte, Tirol, Wattens, 1997, vol. 2. Cemented Carbides and Hard Materials. Pp. 300–314.
6. Ryzhkin, A.A. Sinergetika iznashivaniya instrumental'nykh rezhushchikh materialov (triboelektricheskiy aspekt). [Synergetics of cutting tool materials wear (triboelectric aspect).] Rostov-on-Don: DSTU Publ. Centre, 2004, 322 p. (in Russian).
7. Ryzhkin, A.A., et al. Tverdyy splav na osnove karbida vol'frama (varianty): patent 2531332 Ros. Federatsiya: MPK S22S29/08. [Solid carbide based on tungsten carbide (options).] Patent RF, no. 2531332, 2014 (in Russian).
8. Blatt, F.-J., et al. Termoelektrodvizhushchaya sila metallov. [Thermoelectric power of metals.] Transl. from English. Moscow: Material, 1980, 248 p. (in Russian).
9. Karapetyants, М.K. Vvedenie v teoriyu khimicheskikh protsessov [Introduction to chemical processes theory.] Moscow: Vysshaya shkola, 1975, 333 p. (in Russian).
10. Ryzhkin, A.A., Ilyasov, V.V. O svyazi mezhdu iznosostoykost'yu i fizicheskimi svoystvami instrumental'nykh materialov . [On the relationship between wear resistance and physical properties of the tool materials.] Vestnik Mashinostroeniya, 2000, no. 12, pp. 32–40 (in Russian).
Review
For citations:
Ryzhkin A.A., Bokov A.I., Oleynikova Yu.A. Wear-resistance of high entropy cutting-tool materials. Vestnik of Don State Technical University. 2016;16(3):53-58. (In Russ.) https://doi.org/10.12737/20216
Views: 559
Email this article 