Technoeconomic and thermodynamic aspects of the edge cutting machining optimization
https://doi.org/10.12737/22162
Abstract
The investigation objective is to develop a calculation method of selecting the optimum cutting speed corresponding to the minimum tool-wear rate. The analysis of the known optimization criteria such as tribological, thermal, energy and thermodynamic ones is made. The characteristics of their optimality through the cutting velocity (friction) are identified. Particular attention is paid to the experimental thermodynamic optimization criteria reflecting the fluctuating nature of friction and wear which are developed in Don State Technical University. It is shown that the maximum values of fluctuation criteria through varying the cutting speed characterize the increased dissipation capabilities of the cutting area. The formula for calculating the optimum cutting speed under the conditions of thermal balance on the lathe knife pads is determined. The formula contains cutting mode elements, tool geometry, contact loads and the deformation characteristic of the cutting process - chip velocity factor. The proposed analytical dependence allows selecting the optimum condition using calculations without costly wear resistant experiments.
About the Authors
Anatoliy A. Ryzhkin
Don State Technical University
Russian Federation
Russian Federation
Juliya A. Oleynikova
Don State Technical University
Russian Federation
Russian Federation
Denis V. Moiseev
Don State Technical University
Russian Federation
Russian Federation
Evgeniy V. Fominov
Don State Technical University
Russian Federation
Russian Federation
References
1. Ryzhkin, А.А. Termodinamicheskie kriterii optimizatsii protsessa iznashivaniya. [Thermodynamic optimization criteria of wear process.] Nadezhnost' i effektivnost' stanochnykh i instrumental'nykh sistem: sb. nauch. tr. [Reliability and efficiency of machine tool and development systems: Coll.of sci.papers.] Rostov-on-Don: DSTU Publ. Centre, 1993, pp. 3–16 (in Russian).
2. Ryzhkin, А.А., Shuchev, K.G., Klimov, M.M. Fizicheskie osnovy obrabotki materialov rezaniem. [Basic physics of materials machining.] Rostov-on-Don: DSTU Publ. Centre, 1996, 342 p. (in Russian).
3. Ryshkin, A.A., Vorovich, L.S., Gordienko, B.I. Optimization of Metal Cutting Conditions. Radom: The Institute for Terotechnology, 2000, 315 p.
4. Makarov, A.D., et al. Sposob opredeleniya optimal'noy skorosti rezaniya: a. s. 657918 SSSR . [Method of optimum cutting speed determination.] Invention certificate USSR, no. 657918, 1979 (in Russian).
5. Ryzhkin, А.А. Obrabotka materialov rezaniem: fizicheskie osnovy. [Materials machining: basic physics.] Rostovon- Don: DSTU Publ. Centre, 1995, 291 p. (in Russian).
6. Anukhin, et al. Vybor rezhimov rezaniya trudnoobrabatyvaemykh zharoprochnykh intermetallidnykh splavov teplovizionnym metodom. [Selection of the cutting conditions for hard-to-machine heat-proof intermetallic alloys by thermalimaging method.] Stanki i instrument, 2015, no. 1, pp. 16–20 (in Russian).
7. Artamonov, E.V., et al. Sposob opredeleniya optimal'noy skorosti rezaniya tverdosplavnogo instrumenta: patent 2173611 Ros. Federatsiya: S2 B23 B1/00. [Method for determining optimum cutting speed of the carbide-tipped tool.] Patent RF, no. 2173611, 2001 (in Russian).
8. Silin, S.S. Metod podobiya pri rezanii metallov. [Similarity method under metal cutting.] Moscow: Mashinostroenie, 1979, 152 p. (in Russian).
9. Starkov, V.K. Dislokatsionnye predstavleniya o rezanii metallov. [Dislocation concept of metal cutting.] Moscow: Mashinostroenie, 1979, 160 p. (in Russian).
10. Silin, S.S., Baranov, A.V. Optimizatsiya operatsiy mekhanicheskoy obrabotki po energeticheskim kriteriyam. [Optimization of machining operations on the energy criteria.] Stanki i instrument, 1999, no. 1, pp. 16–17 (in Russian).
11. Tavstyuk, А.А., Lyutov, A.G., Kourov, G.N. Primenenie udel'nykh energeticheskikh parametrov pri optimizatsii i upravlenii protsessom rezaniya. [Application of specific energy parameters during the optimization and control of the cutting process.] Stanki i instrument, 2014, no. 2, pp. 29–34 (in Russian).
12. Zakuraev, V.V., Khadeev, S.I. Otsenka usloviy optimal'nogo rezhima rezaniya po energeticheskim kharakteristikam protsessa. [Assessment of the conditions for optimum cutting mode on the energy performance of the process.] Novokuznetsk: Mezhotraslevoy NTK, 2007, 187 p. (in Russian).
13. Ryzhkin, А.А., et al. Sposob opredeleniya optimal'noy skorosti rezaniya: patent 2521943 Ros. Federatsiya: B23B1/00. [Method for determining the optimum cutting speed.] Patent RF, no. 2521943, 2014 (in Russian).
14. Ryzhkin, А.А. Teplofizicheskie protsessy pri iznashivanii instrumental'nykh rezhushchikh materialov. [Thermophysical processes under the tool cutting materials wear]. Rostov-on-Don: DSTU Publ. Centre, 2005, 312 p. (in Russian).
15. Vinogradov, А.А. Opredelenie optimal'noy skorosti rezaniya po koeffitsientu usadki struzhki. [Determination of optimum cutting speed by the chip shrinkage factor.] Stanki i instrument, 1991, no. 7, pp. 32–33 (in Russian).
16. Bronstein, I.N. Spravochnik po matematike dlya inzhenerov i uchashchikhsya vtuzov. [Handbook on mathematics for engineers and students of the technical colleges.] Moscow: Fizmatgiz , 1962, 608 p. (in Russian).
17. Granovskiy, G.I. Obrabotka rezul'tatov eksperimental'nykh issledovaniy rezaniya metallov. [Elaboration of the experimental studies results of metal cutting.] Moscow: Mashinostroenie, 1982, 112 p. (in Russian).
Review
For citations:
Ryzhkin A.A., Oleynikova J.A., Moiseev D.V., Fominov E.V. Technoeconomic and thermodynamic aspects of the edge cutting machining optimization. Vestnik of Don State Technical University. 2016;16(4):41-50. (In Russ.) https://doi.org/10.12737/22162
Views: 374
Email this article 